[ Back to EurekAlert! ] Public release date: 17-Jul-2012
[ | E-mail Share Share ]

Contact: Jutta Katharina Werner
j.werner@tuhh.de
49-404-287-84321
Kiel University

World record: Scientists from northern Germany produce the lightest material in the world

This release is available in German.

A network of porous carbon tubes that is three-dimensionally interwoven at nano and micro level – this is the lightest material in the world. It weights only 0.2 milligrams per cubic centimetre, and is therefore 75 times lighter than Styrofoam, but it is very strong nevertheless. Scientists of Kiel University (KU) and Hamburg University of Technology (TUHH) have named their joint creation "Aerographite". The scientific results were published as the title story in the scientific journal Advanced Materials on July, 3rd. Today (Tuesday, July 17th) it is presented to the public.

The properties

It is jet-black, remains stable, is electrically conductive, ductile and non-transparent. With these unique properties and its very low density the carbon-made material "Aerographite" clearly outperformes all similar materials. „Our work is causing great discussions in the scientific community. Aerographite weights four times less than world-record-holder up to now", says Matthias Mecklenburg, co-author and Ph.D. student at the TUHH. The hitherto lightest material of the world, a nickel material that was presented to the public about six months ago, is also constructed of tiny tubes. Only, nickel has a higher atomic mass than carbon. "Also, we are able to produce tubes with porous walls. That makes them extremely light", adds Arnim Schuchard, co-author and Ph.D. student at Kiel University. Professor Lorenz Kienle and Dr. Andriy Lotnyk were able to decode the material's atomic structure with the aid of a transmission electron microscope (TEM).

Despite of its low weight Aerographite is highly resilient. While lightweight materials normally withstand compression but not tension, Aerographite features both: an excellent compression and tension load. It is able to be compressed up to 95 percent and be pulled back to its original form without any damage, says professor Rainer Adelung of Kiel University. "Up to a certain point the Aerographite will become even more solid and therefore stronger than before", he points out. Other materials become weaker and less stable when exposed to such stress. "Also, the newly constructed material absorbs light rays almost completely. One could say it creates the blackest black", acknowledges Hamburg's Professor Karl Schulte.

The construction

"Think of the Aerographite as an ivy-web, which winds itself around a tree. And than take away the tree", Adelung describes the construction process. The "tree" is a so-called sacrificial template, a means to an end. The Kiel-team, consisting of Arnim Schuchardt, Rainer Adelung, Yogendra Mishra and Sören Kaps, used a zinc oxide in powder form. By heating this up to 900 degrees Celsius, it was transformed into a crystalline form.

From this material, the scientists from Kiel made a kind of pill. In it, the zinc-oxide formed micro and nano structues, so called tetrapods (illustration # 4). These interweave and construct a stable entity of particles that form the porous pill. In that way, the tetrapods produce the network that is the basis for Aerographite.

In a next step, the pill is positioned into the reactor for chemical vapour deposition at TUHH and heated up to 760 degrees Celsius. "In a streaming gas atmosphere that is enriched with carbon, the zinc oxide is being equipped with a graphite coating of only a few atomic layers. This forms the tanged-web structures of the Aerographite. Simultaneously, hydrogen is introduced. It reacts with the oxygen in the zinc oxide and results in the emission of steam and zinc gas", continues Schulte. The remains are the characteristic interwoven, tube-like carbon structure. TUHH-scientist Mecklenburg: "The faster we get the zinc out, the more porous the tube's walls get and the lighter is the material. There is considerable scope." Schuchard adds: "The great thing is that we are able to affect the characteristics of the Aerographite; the template form and the separation process are constantly being adjusted in Kiel and Hamburg."

The application

Due to its unique material characteristics, Aerographite could fit onto the electrodes of Li-ion batteries. In that case, only a minimal amount of battery electrolyte would be necessary, which then would lead to an important reduction in the battery's weight. This purpose was sketched by the authors in a recently published article. Areas of application for these small batteries might be electronic cars or e-bikes. Thus, the material contributes to the development of green means of transportation.

According to the scientists, further areas of application could be the electrical conductivity of synthetic materials. Non-conductive plastic could be transformed, without causing it to gain weight. Statics, which occur to most people daily, could hence be avoided.

The number of further possible areas of application for the lightest material in the world is limitless. After officially acknowledging Aerographite, scientists of various research areas were bursting with ideas. One possibility might be the use in electronics for aviation and satellites because they have to endure high amounts of vibration. Also, the material might be a promising aid in water purification. It might act as an adsorbent for persistent water pollutants for it could oxidise or decompose and remove these. Here, scientists would benefit from Aerographite's advantages namely mechanical stability, electronic conductivity and a large surface. Another possibility might be the purification of ambient air for incubators or ventilation.

###

Further information:

Original publication: „Aerographite: Ultra Lightweight, Flexible Nanowall, Carbon Microtube Material with Outstanding Mechanical Performance"; DOI: 10.1002/adma.201200491
http://onlinelibrary.wiley.com/doi/10.1002/adma.201200491/pdf

Pictures and further materials can be downloaded at:

www.uni-kiel.de/download/pm/2012/2012-212-1.png
Caption: This graphic shows a detail of the world's lightest material: Aerographite. Open carbon tubes form a fine mesh and offer a low density of 0.2 milligram per cubic centimetre. The picture was taken with a scanning electron microscope (TEM).
Source: TUHH

www.uni-kiel.de/download/pm/2012/2012-212-2.png
Caption: The reactor is heated up to more than 760 degree Celsius. Gaseous zinc and steam leak out. At the image: in the dark areas there is still zinc oxide recognisable. What remains is a graphite shell (light areas).
Source: KU

www.uni-kiel.de/download/pm/2012/2012-212-3.png
Caption: During the building process, the so-called sacrificial template, a crystallised zinc oxide (white), is "sacrificed" when hydrogen is given into the process. Steam and Zinc leak out, the tubes of Aerographite remain.
Source: TUHH

www.uni-kiel.de/download/pm/2012/2012-212-4.png
Caption: The tetrapods of the zinc oxide form an ideal basis for the robust material Aerographite.
Source: TUHH

www.uni-kiel.de/download/pm/2012/2012-212-5.png
Caption: An Aerographite in the making. It offers enormous potentials – e.g. for the production of batteries.
Source: TUHH

www.uni-kiel.de/download/pm/2012/2012-212-6.jpg
Caption: Aerographite is water-repellent, jet-black (which is currently analysed) and electrically conductive.
Source: KU

www.uni-kiel.de/download/pm/2012/2012-212-7.avi
Video: Aerographite can be compressed up to 95 percent and be pulled back to its original form. In contrast to other materials, it thereby just becomes stiffer (Diameter nine millimetres).
Source: KU

www.uni-kiel.de/download/pm/2012/2012-212-8.avi
Video: The very small masses of the Aerographite allow quick changes of direction. It raises itself in an erect position, jumps onto the plastic pole and back onto the table: In that way Aerographite gets electric charge from the pole and emits it to the table.
Source: KU

Contact:
TU Hamburg-Harburg
Press Services
Jutta Katharina Werner
Telefon: +49 40 428784321
E-Mail: j.werner@tuhh.de



[ Back to EurekAlert! ] [ | E-mail Share Share ]

 


AAAS and EurekAlert! are not responsible for the accuracy of news releases posted to EurekAlert! by contributing institutions or for the use of any information through the EurekAlert! system.