Solar panels made in China have a higher overall carbon footprint and are likely to use substantially more energy during manufacturing than those made in Europe, said a new study from Northwestern University and the U.S. Department of Energy's Argonne National Laboratory. The report compared energy and greenhouse gas emissions that go into the manufacturing process of solar panels in Europe and China.
"We estimated that a solar panel's carbon footprint is about twice as high when made in China and used in Europe, compared to those locally made and used in Europe," said Fengqi You, assistant professor of chemical and biological engineering at Northwestern and corresponding author on the paper.
"While it might be an economically attractive option to move solar panel manufacturing from Europe to China, it is actually less sustainable from the life cycle energy and environmental perspective—especially under the motivation of using solar panels for a more sustainable future," he said.
The team performed a type of systematic evaluation called life cycle analysis to come up with these hard data. Life cycle analysis tallies up all the energy used to make a product—energy to mine raw materials, fuel to transport the materials and products, electricity to power the processing factory, and so forth. This provides a more accurate picture of the overall energy consumed and produced and the environmental impact of making and using a solar panel.
Assuming that a solar panel is made of silicon—by far the most common solar panel material—and is installed in sunny southern Europe, a solar panel made in China would take about 20 to 30 percent longer to produce enough energy to cancel out the energy used to make it. The carbon footprint is about twice as high.
The biggest reason is that China has fewer environmental and efficiency standards for its factories and plants and generates more electricity from coal and other non-renewable sources, the authors said.
"It takes a lot of energy to extract and process solar-grade silicon, and in China, that energy tends to come from dirtier and less efficient energy sources than it does in Europe," said Argonne scientist and co-author Seth Darling. "This gap will likely close over time as China strengthens environmental regulations."
The study did not include the energy cost of transporting a solar panel to its final destination. Transportation would magnify the difference even further if it—like 60 percent of all solar installations in 2012—went up in Germany or Italy, Darling said.
The team also compared the numbers for different types of silicon solar panels. Single-crystal solar panels are better at harvesting energy than other types, but take the longest to "pay back" the energy used to manufacture them because the process is more energy-intensive. Multicrystalline panels came next, followed by ribbon silicon panels, which are easiest to manufacture but least efficient—however, their payback time was fastest.
To encourage more sustainable production of solar cells, the authors suggest a break-even carbon tariff. "This would be based on the carbon footprint and energy efficiency difference between manufacturing regions, and would be a better market- and science-based solution than a solar panel tariff," said Dajun Yue, a Northwestern graduate student in You's research group and lead author on the paper.
"The break-even carbon tariff we calculated, which is at the range of €105-129 per ton of carbon dioxide, depending on the possible carbon tax to be imposed by these two regions in the near term, is close to the reported CO2 capture and sequestration cost," You said.
Funding for this research was provided by the Institute for Sustainability and Energy at Northwestern University. The research was performed in part at the Center for Nanoscale Materials, a U.S. Department of Energy user facility.
The paper, "Domestic and overseas manufacturing scenarios of silicon-based photovoltaics: Life cycle energy and environmental comparative analysis," is available online and will be printed in the July issue of the journal Solar Energy.
Argonne National Laboratory seeks solutions to pressing national problems in science and technology. The nation's first national laboratory, Argonne conducts leading-edge basic and applied scientific research in virtually every scientific discipline. Argonne researchers work closely with researchers from hundreds of companies, universities, and federal, state and municipal agencies to help them solve their specific problems, advance America's scientific leadership and prepare the nation for a better future. With employees from more than 60 nations, Argonne is managed by UChicago Argonne, LLC for the U.S. Department of Energy's Office of Science.
The Center for Nanoscale Materials at Argonne National Laboratory is one of the five DOE Nanoscale Science Research Centers (NSRCs), premier national user facilities for interdisciplinary research at the nanoscale, supported by the DOE Office of Science. Together the NSRCs comprise a suite of complementary facilities that provide researchers with state-of-the-art capabilities to fabricate, process, characterize and model nanoscale materials, and constitute the largest infrastructure investment of the National Nanotechnology Initiative. The NSRCs are located at DOE's Argonne, Brookhaven, Lawrence Berkeley, Oak Ridge and Sandia and Los Alamos National Laboratories.
DOE's Office of Science is the single largest supporter of basic research in the physical sciences in the United States, and is working to address some of the most pressing challenges of our time. For more information, please visit science.energy.gov.
AAAS and EurekAlert! are not responsible for the accuracy of news releases posted to EurekAlert! by contributing institutions or for the use of any information through the EurekAlert! system.