News Release

WPI receives $25 million award to bring cold spray 3D printing techniques to the battlefield

Funding from the Army Research Laboratory will support advanced work on cold spray; the portable repair and manufacturing technique could increase the readiness of military vehicles and other units

Grant and Award Announcement

Worcester Polytechnic Institute

See How Cold Spray 3D Printing Technology Impacts the Military

video: Watch: See how cold spray 3D printing technology impacts the military. view more 

Credit: Worcester Polytechnic Institute

Worcester, Mass. - Sept. 10, 2019 - Worcester Polytechnic Institute (WPI) has received a three-year, $25 million award from the U.S. Army Combat Capabilities Development Command Army Research Laboratory (CCDC-ARL) to advance a 3D printing technique that could be used to repair vehicles and other critical technology in the field, avoiding the sometimes extensive wait for new parts and increasing the readiness of military units.

The new award builds on the university's deep and distinctive experience with powder metallurgy and computational tools for materials design gained with nearly $30 million in previous Army funding.

The current Army Research Laboratory (ARL) award will focus on a technique called cold spray, which can be used to repair metal parts or even make new parts from scratch by building up metal layer by layer in a process known as additive manufacturing, commonly known as 3D printing. Cold spray uses a pressurized gas to accelerate metal powders to near supersonic speeds. The force of impact causes the powders to adhere to the metal upon impact. There is no need to first melt the powders. The process can be reduced to a portable handheld applicator, which makes it attractive for use in the field.

"The Army is interested in cold spray 3D printing as a repair technique," said Danielle Cote, assistant professor of materials science and engineering and director of WPI's Center for Materials Processing Data, who is the principal investigator for the ARL project. "It's cheaper to repair a part than to replace it, and you get the equipment back in service faster. The Army's primary interest is unit readiness. If you're on a mission and need to move quickly to a safer place, and a critical part on your vehicle breaks, you're stuck unless you can repair it quickly. That's where cold spray comes in."

WPI's primary focus in this research will be on developing, characterizing, and testing new alloys optimized for use in cold spray. Cote said the characteristics of the metal powders used in cold spray are critically important since the metal is not melted before being sprayed onto a part that needs repair, nor is it heat treated after application. "With most manufacturing methods, metal alloys are alerted by first being melted, and then often heat treated to strengthen or otherwise improve their properties. With cold spray, what you end up with in the repair is exactly what you start with, so the characteristics of the powders are quite important."

WPI will develop and study powders using a variety of state-of-the-art equipment, including instruments acquired as part of the new ARL award. These include tools to study the chemical and structural properties of the powders at the scale of nanometers, such as a SEM/EDS (scanning electron microscope and energy dispersive spectroscopy) unit, a synchronous laser diffraction and dynamic image particle analyzer to determine powder morphologies, and nanoindenters to measure nano-scaled mechanical properties.

The WPI research team, which includes postdoctoral fellow Kyle Tsaknopoulos, will also work with several subcontractors, including the University of California Irvine, the University of Massachusetts Lowell, Penn State University, and Solvus Global. A spinoff of WPI including two recent WPI PhD recipients in materials science and engineering--Aaron Birt (2017) and Sean Kelly (2018)--Solvus Global will provide commercially available powders and modify them to meet the research team's specifications so they can be tested in actual cold spray applications.

Among the modifications that will be made to the powders are unique thermal processing treatments, a technique WPI pioneered, Cote said. Unlike metals used in other metal manufacturing processing, including casting and forging, the alloys used in cold spray do not have to be capable of being heat treated, which gives the WPI researchers access to a wide range of potential materials. However, the properties of cold spray powders can be fine-tuned with the careful application of heat. "This expertise is part of the reason the ARL continues to support WPI," Cote said. "We have discovered that the properties of metal powders can be significantly enhanced with thermal processing, and that is what we are looking to do with this new award."

The alloys chosen for study in this project and the thermal processing regimes used will be determined, in part, using computational models developed at WPI. Grounded in extensive laboratory experimentation and drawing on voluminous databases of metal properties assembled through previous ARL-funded projects at WPI, the models make it possible to custom design powders for specific cold spray applications. "You can do this through trial and error," Cote said, "but it is much more effective to design new alloys and thermal processing protocols with our models, and then test them to verify their properties. WPI's modeling capabilities and experience are what sets us apart from other research teams."

As one example of how custom designed cold spray powders could help improve military readiness, Cote points to helicopter gearboxes, which need frequent repairs. "If you need to replace a part like that, it can take months or even years, and the cost is significant--assuming that the part is available or even still being made. To repair a gearbox with cold spray, you need alloys with high strength, toughness, and ductility. Our methodology will enable us to develop powders that can be used to effectively repair or even manufacture parts like that and get helicopters back in the air quickly."

While the primary focus of the ARL award will be alloys for repairs, Cote noted that "cold spray is a foundational technology with a wide variety of applications, in the military and beyond." As part of the research program, a team of co-principal investigators from multiple disciplines at WPI will explore some promising new applications, including the use of cold spray to apply copper coatings to give equipment antibacterial properties.

Researchers in WPI's robotics engineering program will explore the use of multi-axes robots to automate cold spray. "The Army is especially interested in portable cold spray systems, but the technology can also be used on a larger scale--in industry, for example--and it will be exciting to see how robots can help expand the use of this and other additive manufacturing processes.

"I think there is much potential for this technique. With the work we will be doing with powder development, in robotics, and in a number of other areas, I think we are going to go a long way with cold spray. There really are endless possibilities."

###

About Worcester Polytechnic Institute

WPI, a global leader in project-based learning, is a distinctive, top-tier technological university founded in 1865 on the principle that students learn most effectively by applying the theory learned in the classroom to the practice of solving real-world problems. Recognized by the National Academy of Engineering with the 2016 Bernard M. Gordon Prize for Innovation in Engineering and Technology Education, WPI's pioneering project-based curriculum engages undergraduates in solving important scientific, technological, and societal problems throughout their education and at more than 50 project centers around the world. WPI offers more than 50 bachelor's, master's, and doctoral degree programs across 14 academic departments in science, engineering, technology, business, the social sciences, and the humanities and arts. Its faculty and students pursue groundbreaking research to meet ongoing challenges in health and biotechnology; robotics and the internet of things; advanced materials and manufacturing; cyber, data, and security systems; learning science; and more. http://www.wpi.edu

Contact:
Andy Baron, Associate Director of Public Relations
Worcester Polytechnic Institute
Worcester, Massachusetts
508-831-5916, ajbaron@wpi.edu


Disclaimer: AAAS and EurekAlert! are not responsible for the accuracy of news releases posted to EurekAlert! by contributing institutions or for the use of any information through the EurekAlert system.