image: Figure 1.Nanoimprint fabrication process. The master pattern is transferred to a secondary stamp by hot embossing, followed by resin coating and ultraviolet curing to produce the optical structures.
Credit: Xiewen Wen et al.
Research background
Optical metasurfaces consist of subwavelength nanostructure arrays that manipulate the amplitude, phase and polarisation of light within a planar configuration. They provide compact device architectures for optical analogue computing, quantitative phase imaging, vortex-beam generation and metalens imaging. However, the process complexity and cost associated with electron-beam lithography, deep-ultraviolet lithography and related fabrication methods continue to constrain large-scale manufacturing. By transferring patterns through template replication, NIL offers an alternative route for reproducible, high-resolution fabrication of micro- and nanostructured optical elements.
In addition to fabrication cost, environmental performance is an important consideration in the practical deployment of metasurfaces. Moisture or contaminants entering the gaps between nanostructures can alter the surrounding dielectric environment, affecting the designed phase response and imaging performance. Applying an additional hydrophobic coating is a common strategy; however, the coating can also modify the refractive-index contrast between the structures and their surroundings. For devices based on low-index materials, greater nanostructure heights may be required to achieve the intended phase modulation, even when the coating is accounted for during design, thereby increasing fabrication complexity.
The hydrophobicity of mosquito compound eyes arises from the combined effects of surface micro- and nanostructures and surface chemistry, providing a bio-inspired strategy for addressing these challenges. Accordingly, hydrophobic functionality was incorporated directly into the imprint material, enabling the material to support both optical structuring and surface hydrophobicity without a post-fabrication hydrophobic coating. The fabrication process is illustrated in Fig. 1.
Research highlights
1. Material–process integration for sub-100 nm structure replication
The ultraviolet-curable resin consisted primarily of silicone-modified polyurethane acrylate. X-ray photoelectron spectroscopy and Fourier-transform infrared spectroscopy supported the presence of organosilicon components and the polyurethane acrylate structure. The hydrophobic metalens exhibited a water contact angle of approximately 103°, compared with approximately 32° for the hydrophilic control, demonstrating a pronounced difference in surface wettability.
The master pattern was first replicated onto a TOPAS film by hot embossing to form a flexible secondary stamp. The hydrophobic resin was subsequently applied and cured under 365 nm ultraviolet irradiation to complete pattern replication. Scanning electron microscopy (SEM) of the secondary stamp and imprinted sample showed that the process could replicate structures with lateral feature sizes below 100 nm (Fig. 2), providing a basis for the fabrication of more complex optical devices.
2. Replication of continuous height profiles and generation of a unit-charge vortex beam
A spiral phase plate, also referred to as a vortex phase plate (VPP), was fabricated to evaluate the replication of continuously varying height profiles. White-light interferometry measured a maximum height difference of approximately 1.49 µm, consistent with the design value of approximately 1.5 µm. This result indicates that the process can transfer continuous surface profiles in addition to replicating lateral nanoscale patterns.
Optical measurements revealed an annular intensity distribution with a dark centre after the incident beam passed through the phase plate. Measurements using a Mach–Zehnder interferometer produced forked interference fringes, confirming the generation of a vortex beam with a topological charge of 1 (Fig. 3). Together, the structural characterisation and interferometric measurements support the replication of continuous profiles and their associated phase-modulation functionality.
3. Hydrophobic metalens fabrication with preserved optical focusing
Using the established process, a hydrophobic metalens comprising subwavelength nanopillars of different diameters was fabricated. The sample photograph and SEM images show the overall device structure and the detailed nanopillar arrangement (Fig. 4).
Under 532 nm laser illumination, the hydrophobic metalens exhibited a measured focal length of approximately 4.9 mm. The focal-plane point spread function showed a concentrated intensity distribution, demonstrating the focusing capability of the device. A hydrophilic control fabricated with identical nanostructure geometry also exhibited focusing, providing a basis for comparing the imaging performance of the two devices after contamination and cleaning.
4. Recovery of near-initial imaging performance after a single rinse
The metalens surfaces were treated with a suspension containing powder particles and subsequently dried to simulate dust adhesion before cleaning. Both the hydrophobic and hydrophilic metalenses resolved the test targets clearly in the uncontaminated state.
Following contamination, a single rinse with deionised water removed most surface impurities from the hydrophobic metalens and restored image clarity and contrast to levels close to those before contamination. In contrast, substantial particle residues remained on the hydrophilic control after the first rinse, resulting in pronounced image degradation. Imaging quality improved progressively with additional rinsing and approached the initial level only after a total of three to four rinses. Localised contaminant aggregation and pinning remained observable on the surface (Fig. 5).
Under the particle-contamination and water-rinsing conditions investigated, these comparisons indicate that material hydrophobicity reduces residual contamination and the number of rinses required to recover clear imaging. The principal benefits are improved cleanability and post-contamination imaging recovery, providing experimental support for more convenient maintenance of metasurface devices.
Conclusions and outlook
This study combines a bio-inspired hydrophobic strategy, functional resin materials and high-resolution nanoimprint fabrication to achieve optical structure replication, focusing and imaging, and recovery after contamination and cleaning without an additional hydrophobic coating. The demonstrations using a VPP and a metalens also demonstrate the applicability of the process to different optical structures.
The manufacturing route, based on master-pattern replication and transfer through a secondary stamp, may reduce the cost of repeated device fabrication and provide a basis for further scale-up. The work offers an approach to improving the environmental performance and maintenance convenience of metasurface devices, with potential applications in outdoor imaging, industrial sensing and consumer electronics.
Guided by its motto, “To learn and to apply, for the benefit of mankind”, The Hong Kong Polytechnic University promotes knowledge transfer and university-industry collaboration to translate research findings into solutions with industrial and societal value. The College of Engineering and Applied Sciences at Nanjing University emphasises the integration of science and engineering and links frontier research with practical applications through new research and development institutes and technology transfer platforms. Conducted jointly by the two research teams, this study integrates optical field manipulation, surface hydrophobicity and high-resolution nanoimprint fabrication. In addition to investigating functional innovations in micro- and nano-optical devices, it addresses fabrication and maintenance considerations relevant to practical applications. The findings may provide a technical basis for the research teams at both institutions and associated incubated enterprises to pursue product development and application-oriented translation of micro- and nano-optical devices. By connecting academic research with industrial engineering development, the work reflects an application-oriented approach in which scientific collaboration supports technological innovation and technology transfer responds to industrial needs.
Journal
Light: Advanced Manufacturing
Article Title
Mosquito-eye inspired hydrophobic metasurface enabled by NIL with sub-100 nm resolution