News Release

Annealing-driven absorption mechanisms in TiO₂-Ta₂O₅ high-reflection coatings

Peer-Reviewed Publication

Light Publishing Center, Changchun Institute of Optics, Fine Mechanics And Physics, CAS

Figure | Optical absorption mechanism of annealed thin films.

image: 

Figure | Optical absorption mechanism of annealed thin films. Structural relaxation equivalence between molecular dynamics and experiment. Moderate annealing reduces oxygen-vacancy-related absorption, whereas excessive annealing promotes structural ordering and phase separation, increasing absorption in TiO2–Ta2O5 HR coatings.

view more 

Credit: Zhilin Xia et al.

High-power laser systems are central to precision manufacturing, free-space quantum communication, and inertial confinement fusion. Their performance depends strongly on high-reflection mirrors that guide and control intense laser beams. Even absorption at the parts-per-million(ppm) level can generate local heating, thermal distortion, and eventually optical damage. Reducing this residual absorption is therefore essential for stable and long-lived laser components.

 

High-reflection mirrors are commonly formed by alternating high-index and low-index layers. Tantalum pentoxide is widely used as a high-index material because of its high refractive index, broad operating bandwidth, and favorable cost. Adding a small amount of titanium oxide can further tune the structure and optical properties. However, the lowest-absorption coatings are generally produced by ion beam sputtering, a technique that offers excellent film quality but requires costly equipment and relatively long deposition times.

 

In a new paper published in Light: Advanced Manufacturing, a team led by Zhilin Xia and Xusheng Xia at Wuhan University of Technology investigated whether electron beam ion-assisted deposition could provide a more scalable route to ultralow-absorption mirrors. The method combines relatively low equipment cost with high deposition efficiency and can process more than 20 substrates in one coating run. The researchers deposited TiO2-Ta2O5 and SiO2 multilayers designed for 1,064 nm and annealed them in air from 473 to 873 K.

 

The absorption showed a striking non-monotonic dependence on annealing temperature. The as-deposited mirrors had absorption values of approximately 30 to 50 ppm. Annealing first reduced the absorption, reaching 1.3 ppm at 673 K. This value approaches the performance of mirrors prepared by ion beam sputtering. When the temperature was increased further, however, absorption rose sharply to several hundred ppm at 773 K and exceeded 1,000 ppm at 873 K. The result demonstrates that annealing has an optimum window and that more thermal treatment is not always beneficial.

 

Chemical analysis clarified the low-temperature part of this behavior. X-ray photoelectron spectroscopy showed that the measured-to-stoichiometric oxygen ratio increased from 0.85 in the as-deposited film to 0.95 at 573 K and 0.96 at 873 K. Annealing therefore continued to reduce oxygen deficiency even at the highest temperature. Infrared and photoelectron measurements also indicated an overall reduction in adsorbed water and hydroxyl-related species. Because absorption still increased dramatically at high temperature, oxygen vacancies and water-related species could not explain the reversal.

 

The researchers then examined structural changes. Grazing-incidence X-ray diffraction showed that the coatings remained macroscopically amorphous. Atomic force microscopy, however, revealed isolated protrusions and strong surface roughening after high-temperature annealing. Raman spectra indicated increasing short-range and intermediate-range order, together with different structural responses of Ti—O and Ta—O polyhedra. These observations point to localized ordering or initial crystallization on a scale too small or too sparse to generate clear diffraction peaks.

 

Molecular dynamics simulations provided an atomic-scale picture. As structural relaxation increased, small Ti—O clusters merged into larger aggregates and the amorphous network developed local layered and periodic motifs. The simulations therefore suggested Ti enrichment and phase-separation-like behavior. The high temperatures used in the simulations served as accelerated sampling parameters and represented different relaxation states rather than a direct one-to-one match with the experimental temperatures.

 

First-principles calculations connected this structural evolution to optical absorption. The calculated bandgap narrowed from 3.89 eV to 3.76 eV and then to 3.55 eV as local ordering increased. At the same time, the optical response became more anisotropic and the low-energy extinction coefficient increased. The combined results establish a cross-scale mechanism in which Ti—O aggregation and local ordering modify the electronic structure and increase optical absorption.

 

The study separates two annealing regimes. At lower temperatures, oxygen vacancies dominate absorption and moderate annealing is beneficial. Above the optimum temperature, structural ordering, local phase enrichment, and microstructural inhomogeneity become increasingly important and can overwhelm the gains from improved stoichiometry. This distinction provides a practical guideline for designing thermal treatments rather than treating annealing as a universally monotonic improvement step.

 

By combining an optimized annealing process with electron beam ion-assisted deposition, the team achieved 1.3 ppm absorption in a 1,064 nm high-reflection mirror. The result supports a lower-cost and higher-throughput route toward ultralow-absorption optics for high-power laser applications and offers a general framework for understanding composition-structure-property relationships in composite oxide coatings.


Disclaimer: AAAS and EurekAlert! are not responsible for the accuracy of news releases posted to EurekAlert! by contributing institutions or for the use of any information through the EurekAlert system.