Could two-second microwave pulses make carbon capture cheaper?
A planar-stacked amine sorbent fully releases its captured CO2 within 2-second microwave pulses, cutting regeneration energy to 1.02 MJ per tonne and modeled avoidance cost to 14.09 USD per tonne
Innovation Press
image: Microwave-responsive PEI-based solid sorbent developed for efficient CO2 capture. Pulsed microwave regeneration achieves ultra-low energy use of 1.02 MJ/tCO2. Techno-economic analysis shows CO2 avoidance cost reduced to 14.09 USD/tCO2.
Credit: Wen Y., Jiang P., Zhou M., et al. (2026). The Innovation Materials 4:100224. https://doi.org/10.59717/j.xinn-mater.2026.100224
Carbon capture has a cost problem. The industrial workhorse — bubbling flue gas through liquid amines and then boiling them clean — carries an energy penalty so large that removing a tonne of CO2 runs roughly 50 to 90 USD, while next-generation targets demand regeneration below 2.0 MJ per kilogram of CO2. Solid sorbents promise a way out, but they bring a catch of their own: packing them with enough amine to hold lots of CO2 makes them poor conductors of heat, so regenerating them evenly takes long heating that wastes energy and degrades the material.
A team at Nanjing Tech University reports in The Innovation Materials a design that short-circuits this trade-off. They exfoliated graphene oxide into flat sheets, coated them with silica, and immobilized polyethyleneimine between the layers — a planar-stacked architecture that keeps amine sites exposed and heat transfer paths short. The leading formulation, PEI50-GS7, reached a working capacity of 2.57 mmol of CO2 per gram and kept 95.3% of it after 10 adsorption-desorption cycles, with the layered structure restraining the amine from clumping.
The real departure is how the sorbent lets go. Instead of heating the bulk material, the team fires pulsed microwaves straight into it: the sorbent releases its captured CO2 fully within 2-second pulses. Matching energy input to desorption rate brings regeneration duty down to 1.02 MJ per kilogram of CO2, and 1.21 MJ across the whole cycle — under the 2.0 MJ goal. Spectroscopic and mechanistic analysis suggests the directional microwave electric field weakens and polarizes the C-N bond that binds CO2 as carbamate, easing its escape rather than simply cooking it off.
To test whether the numbers survive scaling, the researchers modeled three 100,000-tonne-per-year plants treating flue gas with 14% CO2: conventional monoethanolamine scrubbing, the same solid sorbent regenerated with steam, and the microwave process. CO2 avoidance costs came out at 53.76, 17.06, and 14.09 USD per tonne respectively, with life-cycle assessment showing lower energy use and greenhouse-gas emissions for the microwave route.
Caution is warranted: the microwave process is demonstrated at the lab and process-modeling scale, and industrial microwave equipment — though already used in other sectors — has yet to run continuously at this scale in a capture plant. Corrosion and amine-degradation problems of liquid scrubbing are avoided by design, but long-duration sorbent cycling beyond 10 rounds, real flue-gas impurities, and full cost uncertainty remain to be tested. Still, cutting both the clock and the kilowatts — seconds instead of minutes of heating, and energy below half of the next-generation bar — is the kind of arithmetic that gets the attention of anyone pricing decarbonization.
###
Ultra-low-energy CO2 capture by planar-stacked solid amine sorbent with pulsed microwave regeneration
The Innovation Materials, 4(3): 100224
https://doi.org/10.59717/j.xinn-mater.2026.100224
Disclaimer: AAAS and EurekAlert! are not responsible for the accuracy of news releases posted to EurekAlert! by contributing institutions or for the use of any information through the EurekAlert system.