When Princeton University engineers want to increase the power output of their new fuel cell, they just give it a little more gas – hydrogen gas, to be exact. This simple control mechanism, which varies the flow of hydrogen fuel to control the power generated, was previously thought impossible and is a potentially major development in fuel cell technology.
The secret of their success is a system in which the fuel input itself changes the size of the reaction chamber, and therefore the amount of power produced. The breakthrough design also adds to the understanding of water management in fuel cells – one of the major obstacles to large-scale deployment of the technology in automobiles.
"It's almost so simple that it shouldn't work, but it does," said Jay Benziger, a Princeton professor of chemical engineering. Benziger developed the technique with Claire Woo, who graduated from Princeton in 2006 and is now pursuing a Ph.D. at the University of California, Berkeley. They will publish their findings in the February issue of the journal Chemical Engineering Science.
The first applications of their design are likely to be in small machines such as lawn mowers, the researchers said. The machines would be easy to use, incorporating a design similar to the familiar acceleration systems of cars that use a pedal to increase the flow of fuel and the power output. More important, Benziger said, the use of fuel cells in lawn care equipment would cut down on a major source of greenhouse gases, especially as emissions from these machines are not currently regulated.
At the most basic level, all fuel cells work by combining hydrogen with oxygen in a reaction that generates electricity, water and heat. In the Princeton system, some of the water produced as a by-product collects in a layer at the bottom of the reaction chamber, while the rest drains to an external tank. By varying the height of the water level in the chamber, Benziger and Woo are able to enlarge or shrink the reaction chamber.
For example, an increased flow of hydrogen into the chamber pushes more water out of the system, lowering the water level and increasing the space available for the reaction to take place. Similarly, a decreased flow of hydrogen causes the pressure inside the chamber to drop, drawing some of the water from the tank back into the system and shrinking the reaction chamber.
The water at the bottom of the chamber also serves to maintain the needed humidity for the fuel cell reaction to take place. This patented "auto-humidifying" design demonstrates an innovative use for the water produced during the reaction, which causes problems in most fuel cell designs.
Conventional fuel cells feature a complicated network of serpentine channels to combine the gases, maintain the appropriate humidity levels and eliminate water from the system. Often, droplets of water clog the narrow channels, leading to inefficient and irregular power production. The Princeton system mixes the gases via diffusion in a simple reaction chamber and relies on gravity to drain the water produced.
Benziger and Woo's reaction chamber is effectively sealed by the water at the bottom of the tank. By preventing fuel from leaving the system, this design ensures that the gases remain in the reaction chamber until they combine. Most traditional fuel cells repeatedly run hydrogen and oxygen through an open reaction chamber, converting only about 30 to 40 percent of the fuel at each pass. Since the Princeton system is closed, 100 percent of the fuel can be used with no need for a large and expensive fuel recycling system.
The work was supported by the National Science Foundation, including a Research Experiences for Undergraduates grant that supported Woo during her summer work. Benziger's lab is now working to connect several of these simple fuel cells in a series to increase the amount of power that can be produced and controlled.
Citation: Woo and Benziger. PEM fuel cell current regulation by fuel feed control. Chemical Engineering Science. February 2007. Published online Nov. 7, 2006. doi:10.1016/j.ces.2006.10.027.
Abstract: We demonstrate that the power output from a PEM fuel cell can be directly regulated by limiting the hydrogen feed to the fuel cell. Regulation is accomplished by varying the internal resistance of the membrane–electrode assembly in a self-draining fuel cell with the effluents connected to water reservoirs. The fuel cell functionally operates as a dead-end design where no gas flows out of the cell and water is permitted to flow in and out of the gas flow channel. The variable water level in the flow channel regulates the internal resistance of the fuel cell. The hydrogen and oxygen (or air) feeds are set directly to stoichiometrically match the current, which then control the water level internal to the fuel cell. Standard PID feedback control of the reactant feeds has been incorporated to speed up the system response to changes in load. With dry feeds of hydrogen and oxygen, 100% hydrogen utilization is achieved with 130% stoichiometric feed on the oxygen. When air was substituted for oxygen, 100% hydrogen utilization was achieved with stoichiometric air feed. Current regulation is limited by the size of the fuel cell (which sets a minimum internal impedance), and the dynamic range of the mass flow controllers. This type of regulation could be beneficial for small fuel cell systems where recycling unreacted hydrogen may be impractical.
Chemical Engineering Science